Referred By: lilylg
select language
Miracle Shield Protects Against Mildew Moisture Water Grease Grime Oil Wear
Miracle Shield is a revolutionary coating that adds luster without the use of harmful silicones or waxes. It protects, renews and prolongs the life of many materials. It cleans, protects and beautifies: leather, plastics, carpets, chairs, TV's, boats, and most painted surfaces. Use it on vinyl, rubber, metal, wood, roofs, concrete, asphalt, stone work and brick work. A coat of Miracle Shield can protect your lawn chairs from rusting, renew your driveway, and extend the life of your roof. It dries to a satin finish that is completely scratch resistant. It even protects against mildew growth, and wear on virtually all non-cloth surfaces. It's non-flammable, non-toxic.
Miracle Shield dries crystal clear without any buffing, and protects without leaving a greasy or oily feel like the other nationally advertised "protective coatings".
Miracle Shield is guaranteed not to chip, crack, peel or yellow. There's no mixing or diluting. Miracle Shield comes ready to apply using a brush, sprayer or roller, or even with a sponge.
To play this video you can use the Real Player Alternative available: Here
Surfaces Miracle Shield can be used on the following surfaces:
Vinyl, Plastic, Rubber, Metal, Interior Wood, Concrete, Asphalt, Stone Work, Brick Work
NOTE: Outdoor applications should be a minimum of two coats solution.
Application
Miracle Shield can be applied as follows:
Finish Miracle Shield, will dry to a satin or low-luster semi-gloss finish. Which is scratch resistant. There is no buffing required.
Miracle Shield hardens best at a surface temperature of 55 degrees or higher on an average of 15 - 20 minutes.
Surface Preparation - In order for Miracle Shield to work properly, the surface must be free from any dust, dirt grease, grime or wax. You can remove any oil, wax or grease with household rubbing alcohol.
Cleaning Properties
In some applications, mild mars, rust and stains have been removed when Miracle Shield is applied.
Viscosity - The thickness of Miracle Shield is determined by the application. The standard application id either by brush, spraying or rolling. With standard applications, about 2 mil. of product is realized per coat.
Product Indications / Preparation
Miracle Shield comes already mixed and ready for use right out of the container.
Cleans with soap and water when wet Cleans with alcohol when dry
Restrictions
Miracle Shield is not to be used on glass, mirrors, chrome or brass, or laquer painted surfaces.
Hazards
Miracle Shield is a mixture of 55% water and 45% chemical solvent.
Combustible fumes are emitted in it's wet state.
Perfectly safe in it's dry state. When applying, ventilate area of application well
Keep container closed when not in use.
Available in 1, 5, or 55 gallon containers.
Surfaces
Use Miracle Shield on the following surfaces:
|
|
NOTE: Outdoor applications should be a minimum of two coats solution.
Finish- Miracle Shield will dry to a satin or low-luster semi-gloss finish. Which is scratch resistant. There is no buffing required.Miracle Shield hardens best at a surface temperature of 55 degrees or higher on an average of 15-20 minutes.
Surface Preparation- In order for Miracle Shield to work properly, the surface must be free from any dust, dirt grease, grime or wax. You can remove any oil, wax or grease with household rubbing alcohol.
Elastomeric Clear Sealer, Finish
Miracle Shield is a Clear Acrylic Elastomeric Sealant designed to seal and protect a wide range of surfaces including wood homes, stone, brick, masonry and concrete, roofing materials and reflective roof coatings.
All white roof coatings start losing their reflectivity properties due to accumulated dirt and other contaminates. Until now clear protective coatings for elastomeric base coatings were not available due to their lack of flexibility which is necessary as roof coatings are designed to expand and contract with a roofs movement.
Miracle Shield also features outstanding adhesion to the applied surface, elongation and recovery capabilities, a combination of UV absorbers and mildewcides enabling it to resist the effects of the most severe climatic conditions. Now all roof coatings can be protected from surface contamination enabling them to perform as intended by reflecting radiant heat away from the buildings interior.
This self cleaning clear coat works much the same way as the clear coatings designed and used on automobile finishes.
Miracle Shield is truly an all-purpose clear sealant and protectant, suitable for virtually any application.
Recommended Coverage: The number of coats depends on surface porosity; however, one coat is all that is normally needed on a well sealed surface.
Drying Time: Will depend on climate conditions. Allow at least 2 hours drying time between coats. First coat must be thoroughly dry before applying second coat.
Limitations: Not suitable for below grade use.
Surface Preparation Surface must be clean and free from dirt, dust, grease, oil, mildew, wax, loose paint.
Application: This product may be easily applied with a quality brush, short nap roller or airless spray equipment. Surface must be clean, dry and sound. Surface must be free of grease, oil wax, mildew or any other surface contaminant. Surface and ambient temperatures should be between 45 and 90 F. Avoid application if rain or condensation could wet surface less than 1 hour after application. Allow 2 hour between coats for best results.
If applying by brush, apply a smooth, generous coat in small areas or cut in large areas first. If applying by roller, apply in even, generous strokes in an "M" or crisscross pattern avoiding excessive re-spreading or reworking. Always maintain a wet edge by brushing or rolling into the previously applied area.
If applying by airless spray equipment, it is recommended to use a unit with a minimum of 2,000 psi pressure, with a 0.013 to 0.021 fluid spray tip. During application, product should be back-rolled to insure proper adhesion and even dispersion. Thinning should not be necessary but use a maximum of 1/2 pint per gallon if it is. Clean up equipment and any spills immediately with warm soapy water and thoroughly rinse with clean water.
Clean-up:
Cleanup immediately after use with soap and water.
Miracle Shield FAQs
Question: What kinds of surfaces can Miracle Shield be used on ?
Answer: Wood, Concrete, Plastic, Vinyl, Rubber, Roofing materials... just about anything.
Question: What does Miracle Shield do ?
Answer: For Miracle Shield a clear, flexible barrier film. Never slippery or oily. Easy application - just apply & let dry. Will not crack or peel. Protects against Ultra-Violet damage with no silicones or waxes. Works on most non-cloth surfaces. Treated surface cleans up with soap and water.
Question: What color is it ?
Answer: Miracle Shield goes on as a slightly milky, translucent liquid. It dries clear. Tinting has not been tested. Try a small sample first.
Question: What kind of coverage can I expect ?
Answer: You can figure that the average spread rate is 300 to 500 sqft/gal and highly dependent upon the porosity of the surface. Concrete pool deck about 300, Cedar yard fencing 400, Stucco wall 250, Old asbestos shingles 300, Wood patio deck 500, Public restroom dividers 600+ when diluted.
Question: How should it be applied ?
Answer: It can be rolled, brushed or sprayed. In vertical applications, it can even be wiped on with a damp cloth.
Question: What is the life time of the coating ?
Answer: High traffic areas should have 2 or more coats applied and life will vary from 2 to 5 years. Vertical applications will last for the lifetime of the surface. A typical roofing application will extend the life of the roof another 10 years.
Question: Is the surface slippery?
Answer: NO. Miracle Shield will have a slight elastic "give" to it's surface which should give a superior non-slip characteristic.
Question: Can I spray Miracle Shield over Therma Guard paint?
Answer: YES! These products work exceptionally well together. Ideal applications include a roof or external walls where you can mate the radiant reflection and insulating properties of TG with the sealing elastic properties of the Miracle Shield.
Question: Can I mix Therm-a-Guard TG Cells with Miracle Shield and get protection and insulation simultaneously?
Answer: YES! TG Cells (packaged dry ceramic spheres) are a new product in the Therma Guard line. Industrial users mix these products with great results and gain the benefits of both products with one application. This is very popular in roof repair applications.
Question: Does Miracle Shield contain harmful chemicals ?
Answer: NO. Miracle Shield is free of all Volatile chemicals and toxins and is recognized as safe, under the Federal Food, Drug, and Cosmetic Act. Non-toxic, odor free and environmentally friendly.
Question: Can Miracle Shield be diluted?
Answer: YES. By doing so Miracle Shield will give you a thinner protective coating
Question: Is there a craft application for Miracle Shield ?
Answer: YES! Absolutely! Paintings, ceramics, wood working projects, jewelry etc. Anything where water proofing, UV and mildew protection would be a benefit. Try it on a test surface first to insure the desired result.